Amp volume issues

diablo175

Well-known member
Supporter
Just a quick question- what do you guys do to deal with changing the volume on your set ups? I have a pretty straight forward set up- guitar goes through wah to Peavey 112- Boss Delay through effects send /return. My problem is I have not found an effective way to boost volume for solos- pedals don't work, volume knob on the multitude of guitars I use don't work well. I LIKE my sound coming from the amp- don't wanna change that. I have a line6 with a volume pedal on the floor board that works great but again, doesn't match up to the tone I get from the Peavey set up. Ideas?

 
Maybe you need an amp with more headroom?

If you are already pushing your amp into saturation then a boost probably won't give you that extra bit of volume you need for your solos. It will just get mushy. I would try to lower the gain or volume on the Peavey and THEN engage the boost. If it works, then look into an amp with more headroom to get you back to the volume you need in a band setting.

 
Have you tried a clean boost (or EQ) in the loop, after the delay? That is my preferred solution, although it has not worked on every amp I have owned.

 
I use a clean boost also. MOF a BBE Boosta Grande. But its also true what.....................................................................................

PirateFlynn is talking about with more headroom. Maybe the 112 isn't giving enough clean headroom to begin with. In that case adding a Clean Boost isn't going to give you...........a Clean Boost?

 
If the power tubes in your amp are already cooking, then yeah, not much you can do other than get a second amp and kick it in for your solos.

 
Maybe you need an amp with more headroom?

If you are already pushing your amp into saturation then a boost probably won't give you that extra bit of volume you need for your solos. It will just get mushy. I would try to lower the gain or volume on the Peavey and THEN engage the boost. If it works, then look into an amp with more headroom to get you back to the volume you need in a band setting.
Nope. In the rehearsal studio, I have the Peavey set at 3 maybe 4. Plenty of headroom left. Since I use the the amp's gain to achieve my preferred tone, switching to a clean channel would require some outboard effects and that's not working- I have a half dozen stomp boxes for distortion, overdrive, fuzz, etc. Not a single one comes close to the tone that lil' Peavey churns out in the lead channel with gain almost all the way up. Bottom line is, I just need a little more volume to put my solo out in front.

 
Nope. In the rehearsal studio, I have the Peavey set at 3 maybe 4. Plenty of headroom left....

..... Bottom line is, I just need a little more volume to put my solo out in front.
With a well-designed serial effects loop and a power section with remaining headroom, a clean boost last in the loop should do this. More volume, same tone.

 
Yeah, if your master is only at 3 or 4, a clean boost in the loop should work. You said you already tried using pedals, but it sounds like you were using them wrong (i.e. before the preamp).

 
Try an MXR Micro Amp Pedal. I use one and it gives a tube amp a slight kick in the ass and gives a little extra umph for solos, works great for a clean boost too.

 
If "a little" volume boost isn't doing it for you, find one of these:

135U-6123_front.jpg


It will give you a lot (i mean...a LOT) of clean boost.

However, if simply using the "same sound but louder" isn't working for you, you may be dealing with the phenomenon of the apparent volume of frequencies changing as volume is increased. Simply put, the exact same "sound" (which means the spectrum of frequencies each at a specific level) will not sound the same to one's ears when the volume is considerably increased (or decreased). It may or may not be possible to "correct" this to your satisfaction with the setup you are using. If you find a boost isn't enough, you could try switching in an EQ (like an MXR 10-band) instead, tweaking freqs until you get approximately what you are looking for.

Good luck.

 
Last edited by a moderator:
My amp repair guy builds his own custom amps for harp players and he has built one of the best boost pedals in the business. He calls it the Rangemax performance booster and I use it with my Fender Rhodes as a pre-amp... it sounds incredible!!!!

rangemax.jpg


RANGEMAX

E N H A N C E D F O C U S – P U N C H – S U S T A I N

Back in the early 1960’s before there was such a thing as high gain, the Dallas Rangemaster Treble Booster was the secret weapon that Eric Clapton, Tony Iomi, and many others used to turbo charge their sound. Fast-forward forty years, apply modern engineering, add a few new features and you have our interpretation of a classic we call the Rangemax.

This is a high gain, clean booster plus a three position equalizer switch, some drive adjustments, and true bypass. We build them with top quality components and each one is hand wired. This booster increases the gain without coloring the sound of your guitar or amp. Connect your guitar directly to the Rangemax for normal use, or use it at the end of your pedal board to restore lost gain and focus. Long output cables are no problem for the Rangemax, because it’s built-in low impedance output driver delivers full signal bandwidth.

Treble Boost delivers a sharper, more defined tone. With high gain amps it will increase the punch without the bottom getting muddy. Notes pop off the fretboard and as the volume is turned up you get a musical top end sizzle.

Full Range Boost will provide flat frequency response. Use this setting to fatten up a single coil pickup or make a Marshall have the full bottom sound of a Mesa.

Mid Boost is full range with a slight reduction in high frequency response. Use this setting to tame a guitar that has a very brite top end.

SPECIFICATIONS

Silver plated Teflon coated wire

Switchcraft connectors

Carbon composition resistors

Select signal path capacitors for optimum tone

Very low noise, gain from unity to +24dB

Low impedance output buffer drives long cables without loss

Drive switch sets transistor bias point

Grit control adds thickness & sustain

EQ switch: treble/mid/full

Hand wired with fanatical attention to detail

Optional 9 volt external input voltage, center negative, 25mW

Battery included, true bypass

Size: 3.5 x 4.5 x 1.5 inches

One year warranty

$179

 
Did you try it through your amp to resolve the headroom issue?
Sorry, try what through my amp? As stated before, I have plenty of headroom with the amp dialed in at 3. Did you mean try a boosting pedal through the FX send/return loop?

 
Back
Top