Special appreciation thread

IMG_0596-1.jpg
Ummm...It would appear that fucking rules!

 
I'll play: an amazing chain of HFC events have led me to this incredible guitar

1. Hamerhead manufactured the 2FIG bridges

2. Kiz had this CO beast built in 2003

3. It got passed around to a host of HFCers

4. Bubs sold it to me

5. Murkat provided an exceptional tone cap that eliminated the "bright" problem

IMG_5296.jpg


This is the Special I always wanted: vintage orange slab of 'hog, sustain block (2FIG), but with a vintage carve neck!

Excuse the crappy iPhone pic (the 'good' camera is recharging for a B'Ball tournament this afternoon). Right now it has an early 80's DiMarzio PAF in the neck, which is good, but Rio is building a Hamer-approved-zebra Buffalo Bucker that should be in there in a few weeks. A Rio Genuine Texas is in the bridge. If I like the combination I plan to have a double creme Genuine Texas wound to replace the double black.

Awesome job out of everyone involved - an incredible guitar! I understand it has made its rounds through the HFC for various reasons, but believe me when I say the "anvil through a plate glass window" problem is absolutely solved. Perfect (for me). When I start to favor a humbucker guitar over my Strat, something good is definitely going on.

 
sq

I'll play: an amazing chain of HFC events have led me to this incredible guitar

5. Murkat provided an exceptional tone cap that eliminated the "bright" problem

believe me when I say the "anvil through a plate glass window" problem is absolutely solved. Perfect (for me).
Can you please tell us know what tone cap you got for the guitar? (value, type, brand?)

I guess is does not affect the tone when tone knob is on 10, right?

So I guess you roll it of some to get the sound you want?

Let us in on the secret /emoticons/default_smile.png

 
sq

sq

I'll play: an amazing chain of HFC events have led me to this incredible guitar

5. Murkat provided an exceptional tone cap that eliminated the "bright" problem

believe me when I say the "anvil through a plate glass window" problem is absolutely solved. Perfect (for me).
Can you please tell us know what tone cap you got for the guitar? (value, type, brand?)

I guess is does not affect the tone when tone knob is on 10, right?

So I guess you roll it of some to get the sound you want?

Let us in on the secret /emoticons/default_smile.png
The guitar was built with the Hamer-spec 0.01 µF cap. I had paid a visit to Murkat Manor back in January to pick up my fantastically reconditioned acoustic guitar, and to pick up some parts Murkat had set aside for me for a Strat project. Among those parts was a 0.022 µF cap that Murkat will hopefully chime in and provide the brand.

When I received the Senior it had PRS McCarty pickups in it. They sounded fine, but the guitar was very bright.

I had a Rio Genuine Texas available (I favor lower powered humbuckers) and one Saturday afternoon curiosity got the better of me - I put the Rio in the bridge - the guitar was harmonically rich, but even brighter (way too bright). I desoldered and checked the potentiometer values and they were very much within spec. Being a simpleton, I made the following association: Guitar too bright → up the cap value. I reached into the parts drawer and found an Orange Drop 0.022 µF, an old-school "Tropical Fish" 0.022 µF and then the magical Murkat 0.022 µF cap. Again, curiosity got the better of me and I stuck the Murkat cap in there. Bliss! The tone control sounded great at all values. Would any of the 0.022 µF caps have done the same thing? Assuming they all test at the same capacitance, theory says yes. However, an entire market has developed around the sonic differences between caps and I won't be drawn into that argument. All I know is this cap sounds fantastic in there and I'm not messing with it!

I should address the "no effect on 10" comment, as this comes up often enough. Yes, tone controls do have an effect on 10, and here's why. The tone circuit could be considered as a filtered drain along the middle of the "pipe" of the guitar's circuit. The filter only allows certain frequencies (dependent upon the value of the capacitor - the "filter") to "drain" out of the circuit. With the tone control on "0" the pot value is 0 kΩ (or really close to it), allowing nearly all of the highs (frequencies dictated by the cap) to drain to ground. As the tone control is increased in number, the value of the potentiometer increases, progressively closing off the drain until you get to "10" on the tone control. At that point, the Pot value is 500k (at least in a Hamer guitar) - the drain is closed up very much, but there are still highs getting through to ground (just not a lot of them). If you were to change to a 1MΩ pot, fewer highs would drain; a 250kΩ pot would allow for more (actually, the same amount as a 500kΩ linear taper pot on 5).

The no-load pots found in some guitars can remove the tone circuit from the equation. At the no load pot's detent, the pot is removed from the circuit (resistance is infinite) and that is the place where the tone control would have no effect.

Edited to add: I found an old PSA thread Murkat posted where a guy was selling them on eBay. They are called ".022uF 200V SUPER PUP MPY2522 Poly-Film Cap Axial Leads" in the auction. Don't see any on eBay right now...

 
Last edited by a moderator:
sq

sq

sq

I'll play: an amazing chain of HFC events have led me to this incredible guitar

5. Murkat provided an exceptional tone cap that eliminated the "bright" problem

believe me when I say the "anvil through a plate glass window" problem is absolutely solved. Perfect (for me).
Can you please tell us know what tone cap you got for the guitar? (value, type, brand?)

I guess is does not affect the tone when tone knob is on 10, right?

So I guess you roll it of some to get the sound you want?

Let us in on the secret /emoticons/default_smile.png
I desoldered and checked the potentiometer values and they were very much within spec.
Thanks. Informative to the max. Is there no way to measure the potentiometer without desoldering it? If so, how would one go about?

 
Thanks. Informative to the max. Is there no way to measure the potentiometer without desoldering it? If so, how would one go about?
If the potentiometer was connected to a circuit, any measurement would include the effects of the connected circuit. Could be there wouldn't be much if any effect, but in this case, I was really trying to get a precise measurement of the true pot value relative its stated value. Disconnecting was the only way I knew to be sure. And realize, since I was changing out a pickup, the guitar was on the bench, hot soldering iron within reach, there really wasn't a great deal of additional effort on my part.

Others more electrically inclined are welcome to chime in - perhaps there is an easier way. And as they do, perhaps they will post more photos of Specials! /emoticons/default_biggrin.png

 
Available now in the FS section. 1981 graphic, fantastic condition, unbelievable player.

HamerSpecialtoothbody.jpg


 
Back
Top